https://popups.uliege.be/esaform21/index.php?id=408 Publications of Auteurs Dermot Brabazon fr 0 https://popups.uliege.be/esaform21/index.php?id=2239 Metal nanoparticles have unique chemical, physical, electrical, and optical properties that make them attractive for a wide range of applications in sensing, anti-fouling surfaces, medicine, and conductive inks. Pulsed Laser Ablation in Liquid (PLAL) is a green method of nanoparticle colloid production, capable of producing ligand-free nanoparticles in solution without the need for hazardous, environmentally unfriendly chemicals. Control of the process parameters can give control over the resulting colloid properties such as particle size distribution. In this work, silver (Ag) nanoparticles (NPs) with average particle size from 2.04 to 19.3 nm and copper (Cu) NPs with average particle size from 40 to 85.9 nm were produced by PLAL) technique. Tue, 23 Mar 2021 14:54:53 +0100 Fri, 02 Apr 2021 16:49:36 +0200 https://popups.uliege.be/esaform21/index.php?id=2239 https://popups.uliege.be/esaform21/index.php?id=756 Additive manufacturing has proven to be a very beneficial production technology in the medical and healthcare industries. While existing for over four decades, recent work has seen great improvements in the quality of products; particularly in medical devices such as implants. Improved customization reduced operating time and increased cost-effectiveness associated with Metal AM for these products offers a new value proposition.  This paper investigates and evaluates modelling methods for the zygoma bone (human jawbone) and explores the most suitable material and optimum design for this critical biomedical implant. This paper proposes an innovative and efficient pre-process methodology that includes modelling, design validation, topological optimization, and numerical analysis. The method includes the generation of the model using reverse engineering of CT scan data and a topology optimization technique which makes the implant lightweight without causing excessive stress concentration. Static structural Finite Element Analysis was conducted to test three different biocompatible materials (Ti6Al4V, stainless steel 316L and CoCr alloys) which are commonly available for metal additive manufacturing. The stresses and conditions in the analysis were that of the human mastication process and all the implant design were tested with the three material types. The Taguchi method was used to determine the optimum design which was found to result in the highest mass reduction of 25% with Ti6Al4V as the implant material. Sun, 21 Mar 2021 13:01:12 +0100 Fri, 02 Apr 2021 17:42:14 +0200 https://popups.uliege.be/esaform21/index.php?id=756 https://popups.uliege.be/esaform21/index.php?id=403 In recent years, recycling the powder leftover within the additive manufacturing process has been attractive for both research, development and industry production. Powder recycling can significantly enhance the sustainability of the manufacturing process, reduce the cost and avoid producing metallic waste as a potential environmental hazard. The first step in reusing the recycled powders in the 3D printing process is to characterize the microstructure and surface quality of the powder for oxidation and impurity analysis. Here, scanning electron microscopy (SEM) and x-ray photoelectron spectroscopy (XPS) have been used for the morphology and surface composition analysis of the 316L powders within the Aconity 3D printer. A new powder collection strategy has been introduced to collect powders from different locations in the powder bed: from the top most and surface of the parts and powder bed after the print terminated, from between the printed parts at different heights. The XPS measurements revealed that oxidation is a common in all the powders compared to virgin powder and more oxidation was detected from the powders collected on the very top of the leftover powder and from surface of the bed. The size of the particles does not change much but larger particles remained at the topmost surface. This finding would help in designing a protocol for collecting the recycled powder from the powder bed and it is suggested to follow a a procedure of collecting powders from the different sections of the powder bed in order to avoid mixing the most and least affected particles. Fri, 19 Mar 2021 18:38:11 +0100 Mon, 12 Apr 2021 12:00:54 +0200 https://popups.uliege.be/esaform21/index.php?id=403